The Cathodic Delaminator is used for rapid checking of product quality and frequently quality control of coated metals. The apparatus consists of a control unit and a temperature control vessel (immersion container) with 8 test receptacles and circulator. Each test vessel has its own constant current source. So you can use up to 8 specimens for testing, independently of each other. The cathodic delamination allows the determination of infiltration of the coating in the damaged area and erroneous retreatments can be made visible (formation of bubbles during pinholes, scratches or stone impact).
Besides the usual applications such as salt spray test and cyclic corrosion tests (CCT), the specimens can be stored and tested in an atmosphere with controlled humidity. Constant settings, as well as rising and falling ramps for temperature and humidity can be programmed quickly and easily using a display with “Touch” function. The Model 618 is ideal for using fast ramps for temperatures or rel. humidity or for slowly increasing/ decreasing over several hours. An additional air conditioner allows the operator to carry out low-temperature cycles down to -40°C and dry heat up to +70°C. Possible test methods include: DIN EN ISO 6270-2 CH, DIN 50958, DIN 55991, ISO 11503, ASTM D2247, BS 3900 Part F2, DIN EN ISO 6270-2 AHT, DIN EN ISO 6270-2 AT, ASTM B117, D171058, ISO 9227, DIN EN ISO 9227 SS, DIN EN ISO 9227 ESS, DIN EN ISO 9227 CASS, P-VW 1210, VDA 233-102
Accelerated Weathering Instrument BANDOL WHEEL®H 532/II Photo-ageing instrument for acceleration of natural weathering
for “wet or dry” cycles. Accelerated Weathering Instrument. A reliable accelerated weathering instrument in a compact design for acceleration of natural weathering. BANDOL WHEEL® was developed for quick but natural weathering, similar to outdoor exposure. To complete the weathering cycle, a mask can be added in the equipment which permits the introduction of obscurity phases without switching off the light source. The samples get a nominal UV radiation level corresponding to about “2 suns”. This permits an important acceleration in weathering that, at the same time, still correlates with natural weathering.
Adaptable anti-slip grip made of aluminum with engraved grid pattern, with freely rotating as well as locked axis for constant force application. incl. clamping chuck adapter to attach the cross-cut single edge, the corrosion scratch tools acc. to van Laar and Clemen as well as many user-specific tools with shaft diameter up to 4mm flexible steel ruler plastic case (without test tip)
Hydraulic load cells are mainly used in static applications. The increased force time (referred to the rated load) should remain constant for at least 1 second. Continuous rapid changes in force may destroy the pressure gauge. It can however be protected against shock loads arising when the load is applied or removed by means of appropriate throttles. All load cells are made of stainless steel.
Instrument for force measurement in connection with DMS force transducers, including integrated mains supply.
These force measuring devices are suitable for universal applications, namely wherever tensile and pressure forces need to be measured with a high degree of accuracy, e.g. in materials testing (Erichsen Tensile Testing Machines UNIMAT® and UNIMAT® + UNICONTROL ®), in reference measuring equipment and in research and development. For industrial purposes too, these force transducers are ideal in the fields of automation, controlling press-in processes and in jointing technology. An extensive accessories program is available. A connection to the Measuring and Display Instruments 975 AP, 980 AP and PHYSIMETER 906 MC is also possible by means of an adapter plug. Measuring range 5kN to 1000kN available.
The Measuring System PHYSIMETER 906 USB is used for the acquisition of mechanical parameters based on wire strain gauge sensors. The ergonomically designed housing made of anodized, high-strength aluminum, is provided with threaded bores at the front side so that an unproblematic connection to the ERICHSEN testing machines is guaranteed – as it was also the case with the preceding models of tensile and pressure measuring devices. As an option a calibration according to VDI/VDE 2624 sheet 2.1 – Measurement of mechanical quantities – Instructions for calibration of mobile force measurement systems – is available. With integrated or external force sensor and USB interface.
We recommend our serie UNIMAT® BASIC 054 testing machines for testing either hard and tough or soft specimens. These tensile testing machines are equipped with two columns and two recirculating ball screws which guide the travelling cross-arm. The upper fixed cross-arm and the base plate in conjunction with the travelling cross-arm between the two from two separate working areas. Available in 10 kN and 20kN ranges.
We recommend our serie UNIMAT® PLUS 052 testing machines for testing either hard and tough or soft specimens. These tensile testing machines are equipped with two columns and two recirculating ball screws which guide the travelling cross-arm. The upper fixed cross-arm and the base plate in conjunction with the travelling cross-arm between the two from two separate working areas. Range 5kN.
The desktop model of the 050 series is small in dimension and require only a minimum of space. The spindle-driven cross-arm runs through two supports which are arranged behind each other and connected at the top by a fixed cross-arm. The lower part of the supports joins a base plate which forms the upper element of a sturdy sheet metal casing. The Model 050 has an electric drive by speedcontrolled DC motor and recirculating ball screw. Range 2kN.
Material testing machine 20 kN, 700 mm travel, 425 mm working width or Material testing machine 20 kN, 1200 mm travel, 425 mm working width
The compact material testing machines of the UNIMAT® BASIC series have been specifically designed to facilitate quality checks simple and fast. The machines are available with a capacity of 3 kN, 5 kN, 10 kN or 20 kN (higher forces on request). The robust construction of massive aluminum and stainless steel makes these testing machines suitable for in-process controls. For driving the cross-arm the Universal Testing Machines are equipped with electric motor drive (microprocessor-controlled, recirculating ball screw and bellows).
The motor including controls as well as the measurement and control system are integrated into the desktop housing. The force is measured via a strain gauge load cell. All testing machines can also be operated as a stand-alone version (with internal software) – without a PC – or with an external Windows program. The testing machines operated via control panel with foil keypad (LCD with 2-line display). (at models 050/052 – integrated into housing; at model 054/056 – side mounting or by remote control)
Digital microscope/camera with 2 million pixels CMOS image sensor and scaleable precision measurement with magnification 20x/40x/200x (also to be used with Paint and Lacquer Testing Machine, Mod. 202 EM)
The special feature of Models 145-60 and 145-100 is the increased drawing speed of the drawing punch which, in addition to the normal drawing speed range of 0 – 1200 mm/min can be adjusted, in an infinitely variable manner and independent of
load, up to 3000 mm/min. This is achieved by using a separate oil circuit, fed by a pump with high volumetric displacement. Contrary to the high speed attachment based on a nitrogen accumulator, here a constant drawing speed behavior is guaranteed over the total displacement of 150 mm. As to the technical design and the options available, including PC control and proportional valve technique, this machines are similar to Models 145. With electro-hydraulic Drive and PLC. With an extensive tooling and accessory list, the machine performs FLC-Test, Bulge-Test, High Speed Test standardized.
Model 161, is an electrohydraulic testing machine to carry out the hydraulic cupping test on all ferrous and nonferrous metals. Specimens up to a size of 400 x 650 mm can be tested. In addition to the actual hydraulic forming process the design of the machine also allows the use of ball punches (FLC) up to a diameter of 100 to 195 mm.
The Models 145-60 and 145-100 belongs to the top-of-the-line models of our sheet metal testing machines. Depending on the demand, there are two versions available: with a drawing force of 600 kN or 1000 kN, including an increased blanking force and blank holder holder force for blank diameters up to 220 mm. The testing machines are equipped with electro-hydraulic drive, fully automatic test sequence and switch-off at specimen failure. This Sheet Metal Testing Machine is not only ideal for the effortless, quick and accurately all important and known-deep drawing tests for ferrous and non-ferrous metals, it is also designed for a large number of additional technological investigations.
Universal Sheet Metal Testing Machine with electrohydraulic drive, fully automatic test sequence and switch off at specimen failure, max. drawing forces200 kN or 400 kN -Model 142-20-BasicandModel142-40-Basic, Model 142-20 and Model 142-40 are available. Capable of performing ERICHSEN Cupping Test, ERICHSEN Deep Drawing Cup Test, FLC-Test, Bulge-Test, High Speed Test including an extensive range available on request. Testing in acc. to ISO 8490, EN 14-58, EN 14-67, EN ISO 20482, JIS Z-2247, DIN EN 1669, ISO 11 531, JIS Z 2249, GB/T 15825
With electro-hydraulic drive, max. drawing force 120 kN and adjustment for pre-setting the blank holder pressure max. 45 kN, blanking head (max. blanking force of 200 kN), automatic test sequence and facility for automatic stop at specimen failure. Drawing force and blankholder force as well as the drawing punch stroke are displayed digitally ERICHSEN Cupping Test, Deep Drawing Cup Test, Bore Expanding Test and Special Tests. Electro-hydraulic drive Program Logic control Fully automatic test sequence
Electronically controlled cupping test machine with electro-hydraulic drive and automatic test sequence, including crack detection, standardized cupping speed and a maximum drawing force of 45 kN – This testing machine is available as a work-top model with compact dimensions which requires only a minimum of space. For the ERICHSEN CUPPING TEST on all ferrous and non-ferrous metals in accordance with the following standards: ISO 8490 DIN 50 101 / 50 102 EN 14-58 ASTM 643-84 EN 14-67 JIS Z-2247
The Model 126 Plus ear measuring instrument is used to make axial measurements of deep-draw cups and can blanks. The typical standards here are DIN EN 1669 and ISO 11531. The device consists of a rotary table, a jaw chuck and a vertical measuring head (with measuring roller and length measuring probe). A jaw chuck secures and centers the cup. The measuring head can be adjusted to fit different sample diameters and heights. During one revolution of the rotary table, the measuring head records the shape of the cup edge (the so-called unevenness). Ear measuring instrument, for cups of 15 – 50 mm diameter, max. 100 mm cup height
The Bead Test Instrument Model 227, enables the quantitative assessment of the technological properties of stamping paints and plastic coatings on cylindrical standard cups. The instrument was designed to produce stresses comparable to those which occur in practice and is particularly suited for use in the development of high quality stamping paints
With electro-hydraulic drive and fully automatic test sequence. ERICHSEN Cupping Test, Deep Drawing Cup Test, Bore Expanding Test, Data Evalution Software with User Test Software, Data logger for recording the measurements such as drawing and blank holder force and stroke. This Sheet Metal Testing Machine is intended for testing materials in the medium thickness range (0.1 to approx. 3.5 mm). It provides rapid an reliable quality monitoring for sheet metal producers and users.
The ERICHSEN Sheet Metal Testing Machine, Model 100, is a bench mounted unit with a cast iron machine body and a cylindrical test head. To conduct the cupping test the sheet metal specimen or foil is entered into an opening through the test head. The screw-in blankholder is set for the sheet thickness using the scale provided. The test head is then tightened manually against a stop on the locating sleeve. This clamps the blank with a force of 10 kN as required by the cupping test standards mentioned above. The clutch pin is pulled outwards from the locating sleeve, the test head is turned clockwise and the cupping process commences. The cupping test value reached is displayed on a digital counter. The forming process and the appearance of the crack can be observed conveniently looking down onto the blank holder.
The overall appearance of a product is influenced by color and gloss. A sample of the same color but higher gloss level is visually perceived darker and more saturated than a low gloss sample. In order to get a uniform appearance, both attributes need to be controlled. The Spectrometers of the very most other suppliers are only able to measure the color value. In comparison with this, the SPEKTROMASTER 565 is able to measure color and gloss both simultaneously! Thus, the cause of a mismatch can be clearly defined in any situation.
PLC controlled test system comprising a basic unit and a control unit, with a motor-driven X-Y- specimen table, a universal holding fixture with vertical linear guide and pneumatic tool feed motion as well as a touch-screen control panel. In acc. To standards AFERA 4001 P11
Tabletop instrument for measuring the thickness of organic coatings on all substrate using the wedge cut principle. Standards ISO 2808, NF T 30-123, DIN 50986, ASTM D 4138. The PAINTXPLORER 548 has been developed to extend the range of the application of the PAINT BORER 518 MC, especially targeting sensitive drillings, particularly into rigid/brittle materials. It is possible that, already at minor eccentric irregular running of the drill used or of its centre axle, such materials can be subject to breaking off of the cutting edges including chipping off, leading afterwards during the optical measurement with the microscope also to limitedly definable transitions between the layers to be measured
Model 750 USB-F for all non-magnetic coatings on steel. Model 750 USB-FN for all non-magnetic coatings on steel and all insulating coatings on non-ferrous metalsThe measuring principle conforms to the DIN, ISO, BS and ASTM norms and standardsThe small and robust thickness gauge LAYERCHECK 750 USB is used for quick and precise, non-destructive coating thickness measurements on metallic substrates. Typical fields of application are e.g. industrial corrosion protection, assessor matters, electroplating and paint shops, the chemical, automobile, shipbuilding and aircraft industries as well as the apparatus and machine construction
The coulometric or anodic de-plating technique is used for measuring the thickness of electroplated coatings on virtually all substrates such as steel, non-ferrous metals or insulating material bases. Typical applications include: nickel on steel, zinc on steel, tin on copper, silver on copper or copper on epoxy This technique simply involves the removal of a small, almost invisible area of coating material. The substrate is not affected. The coulometric method ensures reliable and exact results. Designed for complete ease of use, GalvanoTest requires no specific operator skills and only minimal training before actual measurements can take place. The coulometric principle is the only low-cost method to measure the individual layers of multi-layer systems, for instance chrome plus nickel plus copper on steel one after the other. Connected to the MiniPrint data printer, GalvanoTest provides complete documentation of measuring results and statistics. For specific measuring analysis or later reference, the characteristic voltage curve during the de-plating process can also be printed out.
The Gradient-oven, Model 432, is an indispensable tool for a need-based optimization of baking processes in the coating industry. To assess the baking and drying behavior of paint and powder coatings, resins, plastic materials and similar. The production process can be simulated by programming heat-up speed, baking temperature, and time with temperatures up to 320 °C.
The precisely controlled laboratory high speed stirrers of the DISSOLVER and DISCOVERY 492 series are suitable to produce colloidal suspensions with very fine solid particles integrated by high speed into fluid, as well as for mixing and dispersing of mill feed material within common paint/lacquer matters (disintegration of clusters of powder-type components by shearing force during the dispersing procedure, to cover in ideal case their primary particles with the fluid phase). Available in varying speeds, dispersing disc sizes and accessories.
Model 639 Corrocutter, Test Panel Scratcher to define scratches on coatings of corrosion testing panels.
Simple and low cost test apparatus for continuous salt spray and condensation water testing. The test chamber with a volume of 400 l and all electric and pneumatic components to operate and control the test cycle are incorporated into a compact rectangular cabinet of plastic material. Complete, with specimen holders, storage tank for 90 l salt solution, pressure gauge and LCD for the temperature regulator and test time counter.
For testing vehicle components using cycles of changing corrosive effects in accordance with VDA 621-415. Basic concept, design details and dimensions as for Model 606. Microcomputer to control test cycle (neutral salt spray SS DIN 50 021, alternating condensation water climate SFW DIN 50 017, ambient temperature DIN 50 014). Tests in accordance with international standards, 2 test chambers operable with 1 control cabinet. Operation via SIEMENS touch screen. Various test chamber sizes with test volume of 400 l, 1000 l or 2000 l can be selected regarding the requirements. The test chambers (400 l and 1000 l) are available in circular and rectangular design. The circular design provides even distribution of the salt solution vapour over the entire test zone. When tests are required on larger working parts, it is often not possible to employ a test chamber of circular symmetry. For this reason, as an alternative, rectangular test chambers with a capacity of up to 2000 l (special dimensions upon request) can be supplied. DIN 40 046 ISO 1456 BS 3900/ F4 DIN EN ISO 9227 ISO 3768 NF X 41-002 DIN 50 907 ISO 3769 JIS Z 2371 DIN 53 167 ISO 3770 ISO 7253 SIS 184 190 ASTM B 117 ECCA T 8 ASTM B 287 ASTM B 368 DEF 1053 Meth. 24 ASTM D 1735 DEF 1053 Meth. 36 MIL STD 202 D MIL STD 810 C DIN EN ISO 6270-2 DIN 50 958 DIN 55 991 ISO 3231 ISO 11503 ASTM D 2247 VDA 621-415 P-VW 1210 SWAAT
Compact Corrosion Testing Instrument For tests in accordance with all salt spray standards. The compact Corrosion Testing Instrument, Model 606-Basic, to perform salt spray and condensation tests, is made of impact resistant, eco-friendly polypropylene material and is delivered in a rectangular design in the following chamber volume capacities: 300 l, 400 l, and 1000 l (the new 300L size in a vertical orientation)
For condensed water tests (constant humidity) in accordance with DIN EN ISO 6270-2, DIN 50018, DIN 53771, DIN 55358, DIN 55991 T1, ISO 11503, ISO 3231, ISO 4541, ASTM D 2247-97, BS 3900:F8 and NF T 30-055.
Compact instruments to determine the resistance to exposure to sun light using a Xenon high pressure lamp (1500 W or 2500 W). Adjustable levels of irradiance, uniform illumination by special mirror system, exchangeable filters for variable UV fraction. Programmable flooding system for periodic wetting of specimens available.
The HYGROTHERM 519 Smart model is equipped with a PLC control unit. The necessary test parameters are entered via a touch screen display with user-friendly menu navigation. Allows a fully automatic or manual process for testing the behavior of corrosion protection systems when exposed to condensation in accordance with DIN EN ISO 6270-2. Suitable for conducting condensed water constant (CH) and alternating climate (AHT, AT) tests and also for carrying out tests in an atmosphere containing sulfur dioxide according to DIN EN ISO 6988.
Inexpensive apparatus for testing the corrosion resistance of specimens in condensation water climate with or without SO2 addition in accordance with different standards. Robust 300 l plastic chamber with front door loading. A larger version with 1000 l test chamber volume can be supplied in special design.
This hand operated instrument complete with carbide cutting tip provides a convenient means of scoring a 1 mm wide rectangular track in a surface coating – for corrosion tests.
Model 428 Handcutter, for specimen preparation in corrosion testing.
Portable instrument to apply defined scratches through coatings on specimen panels used for corrosion tests. Compact construction for fatigue-free operation. Scratch tool with van Laar geometry. Defined adjustment of the depth of the scratch in increments of 25 microns
A practical instrument with tungsten carbide tip 0.5 mm in diameter. The instrument is used for standardised scratching of corrosion test samples.
The TINT TESTER 527, has been developed especially for brightness measurement of dark, uncured coatings such as paste pigment applications on flat surfaces, to determine the tinting strength according to ASTM D 3265 and ASTM D 2745. Besides this special application, the instrument can also be used as a standard reflection photometer to measure the brightness of solid substrates (coatings, paper, plastics, etc.) according to ASTM E 97.
Microprocessor controlled color comparison cabinet. Automatic operation based on manually preset program sequences. 3 types of illuminants: A, D65 and TL84. Facility for adding UV light to clarify response to the fluorescent effect. Control panel with foil pad keyboard and LCD. Display of operating hours and number of switching cycles for each light source. Accessories: Pivoting specimen table, light diffuser.
Model 562MC Glossmeter, dual angle with 20 and 60 degree geometry in acc. to EN ISO 2813, DIN 67 530, ISO 7668, ASTM D 523.
Model 560MC Glossmeter, single angle of 60 degree geometry and in acc. to ASTM D 523, DIN 67530, EN ISO 2813 and ISO 7668. The 560MCX-S for measurements on small specimens (3mm aperture).
Consisting of measuring head and supply and display unit for non-contact gloss measurement on the process line. 10 mm measuring distance. Built-in calibration standard and dust protected versions on request. An electrically controlled traversing device carrying the measuring head can also be supplied.
Three measuring geometries in one portable instrument: 20º, 60º and 85º. With data storage and statistical functions as well as interface for data transfer to PC. Battery operated instrument.
Damp photographic paper is pressed by a rubber pad under defined force onto the film surface in accordance with DIN 53 159. Evaluation of chalking mark by comparison with sample scale.
Operation via keyboard and display adjustable stroke rate and stroke path Parameter storage for 20 test cycles up to 3 tests simultaneously. For the assessment of the washing and scrubbing resistance as well as cleanability of dispersion paints (specifically ”wall paints”)., The wide range of its adjustable parameters allows also some further tailored/customized testing matters (for example for testing cleaning agents/solutions, etc.) as well. In the above standard applications a matt black PVC foil will be coated, and – if required – soiled in a defined manner. After clamping into the device it will be exposed under the influence of a washing liquid the stress of the moving scrub body.DIN 53 778-2 ASTM D 2486 DIN EN ISO 11998
Internationally established abrasion test instrument. Standardized tests for 8 plastics decorative coatings, paints etc. Suitable for abrasion simulation of all types by applying appropriate abrading wheels and the use of a wide range of accessories.
Pocket instrument for scratch resistance (mar resistance) of painted or plastic surfaces. Test body (plastic, copper or steel disc) is applied with a pre-set force and drawn across the test surface. Spring force 0 – 20 N divided into 3 measuring ranges. (Model 435S for adhesion testing)
For various scratch hardness tests, e.g. in accordance with the process used in the industry making plastic panels. 5 different tools with diamond or carbide scratching tip. Force range: 0.1 – 10 N.
This successful and extremely useful scratch hardness tester is in the form of a pocket instrument. Also for tests on curved surfaces. Carbide ball tip, diameter alternatively 0.5/0.75/1.0 mm. Spring force 0 – 20 N divided into 3 measuring ranges. (Model 318S designed with rolling head) This instrument has been designed for the measurement of the hardness of protective coatings. The degree of hardness of paint films, plastic coatings, etc. can be accurately measured and recorded with the Hardness Test Pencil, Models 318, 318 S and 318 C, no matter whether on a level or curved surface, small or large.
Damping of the oscillations of a pendulum resting on the coating material in accordance with the standards. Konig and Persoz pendulum interchangeable. Dust cover included in the basic unit. Optional accessories: Opto-electronic counter with acoustic signal at test end with manual or automatic deflection of pendulum.
Pencils of various grades of hardness are moved over the painted surface at an angle of 45° to the horizontal with a force of 5 N, 7.5 N or 10 N (± 0.1 N). The pencil hardness is defined by those two grades of hardness the softer one of which just produces a writing trace while the next harder one leaves a perceptible scratch on the coating.
A steel block with circular indented inserts is applied onto the test surface and produces a pressure mark, the length of which is measured with a microscope. The impression hardness in accordance with Buchholz is established from the length of the impression, using the standard table
The optimized scratch hardness tester LINEARTESTER 249 is intended, in addition to its original purpose of application, i. e. to establish the ability of a surfaces to resist damage by scratching, also for several other tests: – Scribe/Scratch tests – To and fro-cycle abrasion tests – Crockmeter tests – MEK tests, tests determining the resistance against solvents in general or wipe test, respectively. Scratching force in the range of (0.5 – 20) N, with electromotive drive, including circular level, power pack and operating manual.
The MULTI GRIT TESTER 508 VDA is a stone hammer blow testing instrument that at first was developed in co-operation with the “Verband der Automobilindustrie (VDA)” (Association of the Automotive Industry) but now also meets the specifications of national and international standards. The MULTI GRIT TESTER 508 VDA is used to assess the ability of single and multiple layers of paints and similar coating materials to stand up to the impacts caused by small bodies of low mass hitting the specimen at high speed as experienced on road and rail vehicles and other equipment used in the transport field. The new MULTI GRIT TESTER 508 SAE is a stone hammer blow testing instrument equipped with an adjustable impact angle, contrary to the execution of VDA. 508 VDA acc. To DIN EN ISO 20567-1, FORD FLTM BI 157-06, RENAULT D24 1702, PSA D24 1312, DAIMLER DBL 5416. 508 SAE acc. To SAE J 400, ASTM D 3170.
Options include: Impact Cabinet RIMpact I (for models 508/SAE and VDA) Enables the user to test complete rims respectively and in principle several other larger sized specimens.
Analysis system GRITSCAN for the automatic evaluation of impact images. It is a surface analysis system consisting of a combination of hardware and software, especially for capture and analysis at impact images.
Practical test method to determine the quality of coated metal sheets by deformation in a sudden blow The Bend and Impact Tester is used to measure both flexibility and impact resistance of light gauge sheet metal, or tube stock, coatings in a single operation. The test simulates punching, beading, crimping and similar operations.
Portable and handy instrument especially designed for tests on enamel in accordance with DIN 51 155. Enables the user to carry out tests on site.
ERICHSEN Impact Tester 304 are used for determination of impact resistance, deformability and tensibility of coatings and substrates as well as adhesion of the coatings. The ball impact test simulates this type of stress under standardised conditions. A ball punch of defined weight the bottom of which is of fixed diameter, is dropped freely down a guide tube from an agreed or variable height. ASTM D 2794 ISO 6272-1 ISO 6272-2
To measure adhesion of coatings in accordance with ASTM D 4541 by pulling off stuck on dolly. Robust unit requiring no electrical supply and therefore particularly suited to application in the field. Complete test case with necessary accessories. 4 versions for measuring ranges 5/10/25 N/mm2 and special version for measuring on concrete surfaces.
The motor-driven SCRATCH HARDNESS TESTER 430 P-Smart is a universal testing instrument designed for carrying out a wide range of tests on varnished and plastic surfaces to determine their resistance to scratches and cuts. Single cuts, parallel cuts and – by turning the specimen by 90° – cross-cuts can be applied to test panels of various thicknesses. The SCRATCH HARDNESS TESTER 430P-Smart is particularly provided for adhesion tests using the cross hatch cut method (in accordance with all mostly required standards) and for specific plastics tests according with Opel (scratch resistance and writing effect). For these as well as for further tests numerous setting possibilities on the basic instrument and a large variety of test tools are available to perform DIN EN ISO 2409, ASTM D 3359, JIS K 5600-5-6, SNV 37 111, VDA 621-411, ECCA T6, GME 60280, GMW14688 & many other test methods. Using the SCRATCH HARDNESS TESTER 430 P-Smart, series testing can be conducted with much greater ease. The results of testing are reproducible and well-defined. Optionally with manually actuated/motor-driven loading force and manually actuated/automatic test panel turn. Operation, documentation and data management via ERICHSEN-App
Successful instrument for producing a cross cut pattern in the coating to be tested Besides the universally applicable single blade instrument with folding ruler. 5 special multi-cutter versions available for tests in accordance with the standards listed. ISO 2409, EN ISO 24091), JIS K 5600-5-6, EN 13523-64(formerly ECCA-T6), ASTM D 3359, VDA 621-411, DBL 5416, ISO 2409-1972, BS 3900:E6, NF T 30-038 (all withdrawn)
Available option is the CrossScan 295/XVI Automatic Cross Hatch Cut Rating System ; evaluation software; consists of a handy dome for placing on the crosshatch pattern to be evaluated; equipped with camera, LED lighting and potentiometer for intensity control of lighting (5% – 100%). The evaluation takes place via the included software (PC not included).
Precision instrument for measuring bendability in accordance with standards for flexible materials (metal and plastic foils, cardboard, paper etc.; max. thickness 3 mm). Outstanding good measuring accuracy (up to 0.1 %) achieved with motorized measuring process. Analogue and digital versions available, with accessories covering a total measuring range of 0.01 – 10.000 Stiffness Units.
To establish the limiting extension of coating materials on sheet metal specimens by bending around a conical mandrel (1/8″ – 1 ” or 3 mm – 38 mm dia.). From the diameter of the mandrel at the point where the crack starts, the maximum relative extension of the coating can be calculated. With quick-clamping device for faster operation.
Lever-type instrument for testing the flexibility and the adhesive properties of coatings when these are subjected to bending stresses. With 14 easy exchangeable mandrels (diameter 2 – 32 mm). Testing with the cylindrical mandrel bending tester determines the greatest cylinder diameter at which a coating will show cracking or flaking subsequent to bending. Model 266 S allows the testing of samples up to a width of 100 mm.
Non-destructive coating thickness measurement on steel (F) and non-ferrous metals (N), measuring sensors up to 15 mm (F) and 7 mm (N) The MiniTest is ergonomically designed and its rounded shape allows the MiniTest gauge to fit perfectly into the palm of your hand. Designed for utmost flexibility for quality control and inspections.
For non-magnetic coatings on steel using the non-destructive magnetic pull-off technique. No electrical current required. Measuring result held mechanically. With unique automatic measuring system for reproducible results, even under extreme measuring conditions. 11 versions for a total measuring range 1 micron – 20 mm, also for electro-plated nickel layers on various base materials.
Inexpensive instrument using the magnetic pull-off method for rapid non-destructive measurement of non-magnetic layers on steel. Measuring result held mechanically. No electrical supply required. Measuring range: 25 – 700 microns.
Thickness measurement of all coatings on any substrate Measurement of individual layers of a multi-layer coating
Universal Thickness Measuring Instrument Thickness measurements in accordance with the standardised wedge cut method. Combines the advantages of P.I.G. 455 with greater ease of operation: a conical bore of defined angle is made in the coating. Measuring microscope, easily and accurately focused over the cut out. Minimum specimen damage allows a large number of test points. Specimen holder for very small specimens (10 mm dia.) available. DIN 50 986 ISO 2808 ASTM D 4138 ASTM D 5796
With the 518 USB version, connectable to a PC, laptop/WINDOWS-tablet, a convenient digitally supported way is given for visual recognition/ detection/measurement and documentation. An appropriate software is included
To measure the thickness of foils, card, paper, with and without coating. Indispensable for scrubbing resistance tests on Leneta foils and for colour and opacity measurements on contrast cards. Measuring range 1000 microns, accuracy 1 micron.
A successful instrument using the standardised wedge cut method. Indispensable for film thickness measurement on any substrate. In the case of multi layer coatings total and individual layer thickness can be measured. Measuring ranges 200/500/ 1000/2000 microns. Also for adhesion tests in accordance with AS 1580 (method 408.1).
One instrument only for 4 measuring ranges: 5 – 100 microns, 100 – 500 microns, 300 – 700 microns, 700 – 1500 microns. This comb-shaped instrument, made of stainless steel, stands out for high accuracy.
Inexpensive simply operating instrument. The stainless steel “comb” with tooth lengths varying by equal amounts is applied perpendicular to the wet film and the film thickness can be read off on the last tooth that made contact with the wet coating. 3 versions with measuring ranges 120/600/1200 microns. Also available is the Model 333-S: Large version acc. to BASF for road marking paint
Same principle of measurement as Model 233. For measurements on wet films the contact point is raised by means of a knurled screw and then lowered until it touches the surface of the wet film.
A hardened and ground double wheel with an eccentric cam in the middle is rolled over a newly applied film. The wetting line on the middle cam is read off on a scale as wet film thickness. Total measuring range: 1500 microns, available in 8 different sub-ranges.
The difference in level between substrate and film surface is gauged by the contact point of the dial indicator. Measuring range 0 – 1000 microns in 5 micron divisions.
The Model 504-V drying recorder automatically registers and records the drying behavior of paints and similar coatings. This device consists of a metal housing with cover plate which also serves as a support surface for 6 glass strips measuring 305 x 25 mm, on which the coatings to be tested have been applied. Using six testing needles the Drying Time Recorder can conduct testing with variable testing speeds, and choice of 20 pre-programmed running times from 7.5 minutes to 96 hours. Other running times (in increments of 30s) are available on request.
For testing the degree of through drying of a coating. A test plunger faced with nylon fabric and loaded with a defined weight is lowered onto the test surface for a period of 10 s, and then turned through 90º. The resulting effect on the coating is evaluated after lifting the test plunger
A simple plunger type press for measuring Degree of Dryness in accordance with DIN 53 150 in the range from 2 to 7. A glass tube Ballotini dispenser to measure Degree of Dryness 1 is available as accessory.
The Film Applicator and Drying Time Recorder COATMASTER 510/510 XL, enhanced successor of the worldwide established COATMASTER 509 MC, is a compact combined film application and testing instrument equipped with a foil keyboard, and performing two basic functions if the appropriate accessories are selected: the use as a high-precision film applicator, the determination of the degree of dryness in accordance with DIN 53 150 and the performance of comparative drying tests. Exchangeable Specimen Platforms : Glass plate, Vacuum suction plates for foils, papers and cards, in different versions – also electrically heatable, adjustable for temperatures up to 140°C (upon request up to 150 °C).
Model 481 Autospray Type APL 1.2, spray applicator for test panels in acc. to DIN EN 50016, ATEX EX II 2G p II T3 and
VDE 0170/0171, Teil 3.
Produces 6 or 10 film strips of graded thicknesses in one operation. Film thickness range: 10 – 500 microns. Suitable for assessing paint properties in relation to film thickness: opacity, colour strength, drying properties etc.
A film applicator with variable gap height. Clearance adjustable in the range 0 – 1000 microns by means of a micrometer screw (accuracy 1 microns). Available for film widths 80/150/220 mm
The UNICOATER 409 is a budget-priced, motor-driven film applicator for defined and reproducible application of coating materials on very different plain substrates. Irregularities and inaccuracies inevitable when applying films by hand, are avoided using the UNICOATER 409. This results in the following important advantages: – an even and reproducible film thickness over the whole surface – the possibility to produce very quickly a large number of identical samples.
An inexpensive special film applicator with 4 heights of gaps for widths of film 13/40/60/90 mm. Standard gap heights 30/60/90/120 microns. Also available for other wet film thicknesses in the range from 15 – 2000 microns. Model 360 is made of corrosion resistant steel.
Well proven film applicator for any kind of film forming liquid. Particularly suitable for applying films to flexible substrates. Available for film widths 80/150/220 mm and wet film thicknesses between 10 and 200 microns. Made of stainless steel.
To produce specimen panels with an evenly applied paint film of defined thickness. Variable speed from 100 – 2500 min-1
Duplex film applicator for film widths 80/120/180/230 mm. Made of corrosion resistant steel. The two gaps can be chosen as desired from the range 15 – 2000 microns.
24 test card versions available, in different sizes, patterns and colourings, including special penetration cards for watery systems. Test charts to determine the hiding power and contrast ratio of pigmented systems in organic solvents.
A robust instrument for gauging the degree of fineness-of-grind of liquid dispersions of pigments in the range 0 -15/25/50/100 microns. The substance is filled into the wedge-shaped grooves and drawn down with a blade. Rippling occurs at the point where pigments particles are bigger than the depth of the groove measured in microns.
For rapid determination of density of liquids. A sphere of volume 100 or 10 ml is immersed in a beaker the contents of which have been previously weighed. The increase in liquid level given in gms corresponds with 100 or 10 x the value of the density. The equipment is easily cleaned after use.
To measure the density of coating materials and similar liquids. Robust and light weight design, made of black anodized aluminium or stainless steel. Available for 50 or 100 ml capacity. Can also be provided with certification from the official Bureau of Weights & Measures (EICHAMT) .
Software for rapid conversion between viscosity and efflux time, for use with standardized flow cups. Converts between dynamic and kinematic viscosity. Clearly arranged graphics, easy to use.
For rapid conversion between different viscosity units (ASTM seconds, DIN seconds, cSt, Engler degrees, Krebs-Stormer units, Gardner-Holdt units) at defined temperatures (ICI Scale for the viscosity/temperature relationship).
Parallel strips of wet film are applied to a substrate using a special paint applicator frame made of stainless steel and featuring slots of various heights. The sag tendency is determined in a vertical flow test, the levelling tendency is ascertained when the specimen is horizontal. The specimen panel is examined visually after the coating has hardened.
Rapid determination of the viscosity of any type of fluid, as for instance paint, varnish, wet enamel, photogravure ink, dye and lacquer for leather, oil, fat, foodstuff etc. Particularly suitable in the workshop. Simple Dip Flow Cup, available in five sizes as a set or individually.
Well-known, handy instrument for quick and convenient establishment of viscosity, directly from the container, by simply dipping in and measuring run out time. Internal dimensions in accordance with DIN 53 211 (Model 321) and ISO 2431 (Model 322), respectively.
A simple reliable instrument for checking the required brushing or spraying consistency of coating materials. Invaluable for users of paint. Serves also as stirrer for thinning down small quantities.
Flow Time Measuring Instrument CUPTIMER 243 USB with USB interface for data storing. Opto-electronic Measuring Instrument for exact Determination of the Flow Time by using Standardized Flow Cups, for Viscosity Measurements. Adaptable for use with DIN, ASTM and ISO flow cups (also suitable for AFNOR cups).
A flow viscometer conforming to international standards. Optional accessories: Adjustable tripod and thermostatically controlled jacket to ensure reproducible results; thermometer and digital stop watch with calibration certificate.
Fully automatic cupping and deep drawing cup test machine for testing the ductility of coated, ferrous and non-ferrous metals (e. g. coil coatings, lacquered, plastic coated or electroplated materials). The testing machine is provided with an electro-hydraulic drive and a maximum drawing force of 200 kN. The testing machine is equipped with manometers for indicating the sheet holder force and the drawing force. The drawing punch stroke is displayed digitally For testing lacquers and paints of all kinds for elasticity and adhesive quality using the Erichsen Cupping Test in conformity with DIN ISO 1520, ISO 1520, BS 3900:Part E4, NF T 30-019 and SIS 18 41 77 and deep drawing cup test. In acc. To ISO 1520.
For testing lacquers and paints of all kinds for elasticity and adhesive quality using the Erichsen Cupping Test in conformity with DIN ISO 1520, ISO 1520, BS 3900:Part E4, NF T 30-019 and SIS 18 41 77 and deep drawing cup test in acc. To ASTM E 643-84, DIN EN 1669, ISO 11531 and ISO 1520.
Lacquer and Paint Testing Machine, Model 202 EM, with electromotive drive, equipped with a laterally opened test head, test tool in accordance with DIN EN ISO 1520, electric installation for connecting the illumination of the microscope as well as a digital display for the acquisition of the ERICHSEN cupping value, with integrated preselection counter for setting the maximum cupping value required. The machine is operated via touch panel. For testing lacquers and paints of all kinds for elasticity and adhesive quality using the: Erichsen Cupping Test in conformity with DIN EN ISO 1520, BS 3900:Part E4, SIS 18 41 77 and NF T 30-019 on sheet metal specimens up to 1.5 mm thick and max. 100 mm width Test parameters such as speed (2 – 60 mm /min)
Simple and inexpensive mechanical testing machine for ERICHSEN Cupping Test on painted or plastic coated sheet metal specimens up to 1.25 mm thick.